Tender For purchase of consumables - department of electronics engineering, wire (1sq.mm. coil) red, wire (1sq.mm. coil) black, wire (1sq.mm. coil) green, bulb(filament)-40w, bulb(filament)-60w, bulb(filament)- 100w, straight batten holder, switch-one way, bread board, capacitors-0.22 f (400v), capacitors-0.47 f (400v), capacitor(disc)-100pf, capacitor(disc)-220pf, capacitor(disc)-330pf, capacitor(disc)-470pf, capacitor(disc)-0.1 f, capacitor(disc)-0.01 f, db3(diac), diode-1n 4007, fet-bfw 10, ic 7400, ic 7402, ic 7411, ic 7432, ic 7447, ic 7446, ic 7473, ic 7474, ic 7476, ic 7483, ic 7486, ic 7490, ic 7493, ic 74150, ic 74151, ic 555, ic 565, ic 741, ic- ad 534, ic-ad 633, ic-cd 4046, ic-lm 311, ic-lm 324, ic-lm 380, ic- lm 723, ift, resistors-1.2k (0.5w), resistors-1.5k (0.5w), resistors-2.2k (0.5w), resistors-4.7k (0.5w), resistors-56 ohm(0.5w), resistors-1k (0.5w), resistors-10k (0.5w), scr-2p4m, single strand wire(22 swg), transistor-bc 107, transistor-bc 194 b, ujt- 2n2646, battery water, battery 9v, combination plier(210 mm), insulation tape, paper cutter blade(18 mm) (1 box), thinner(sp 58 nc), 2 pin chord wire, solder 60/40, linear potentiometer (10k), linear potentiometer 100k, linear potentiometer 4.7k, linear potentiometer 1m, linear potentiometer 22k, led (red), led (green), led (blue), led (yellow), hdmi cable (1.5 meter), 2 pin chord wire (1 .5meter), solder 80g (60/40), insulation tape (nc), transistor (bc548), transistor (bc 547), wire stripper (), resistor (270 ohm,0.5w), resistor (1k,0.5w), resistor (10k,0.5w), resistor (120k,0.5w), linear potentio meter (10k), linear potentio meter (100k), linear potentio meter (4.7k), linear potentio meter (1meg), linear potentio meter (22k), ic (741), ic (7805), ic (cd4016), capacitor (2200mf,50v), capacitor (0.01mf), capacitor (0.1mf), led (red), led (green), led (blue), single strand hook up wire (23awg/coil), digital ic (7400), digital ic (7402), digital ic (7404), digital ic (7408), digital ic (7432), digital ic (7486), digital ic (7410), digital ic (7411), digital ic (7420), digital ic (7421), digital ic (7473), digital ic (7474), digital ic (7476), digital ic (7490), digital ic (7493), digital ic (74154), digital ic (74151), digital ic (7483), ppt slide changer with laser pointer (2.4g hz), pen drive (64gb), crimping tool, rj 45 connector, rj 45 cable tester, extension board (4-way), department of electrical and electronics engineering, capacitor bank: 10 kva 440 v 3 phase, capacitor: 60 mfd 440 v, capacitor: 50 mfd 440 v, 3 pin plug: 5a, 250v, pvc wire: 1.5 sq. mm, contact switch: 4 pole 15a 250v nc, surge protective device dc 270v 20ka, surge protective device ac 270v 20ka, 3core wire 1.5 sq. mm, capacitor: 33 mfd, capacitor: 10 mfd, resistor: 820 ohm, resistor: 1.5 kilo ohm, push button nc, push button no, floating switch, soldering lead, relay, buzzer, wire: single stranded, dc motor, battery, npn transistor, cro probe, ic 7476, ic 7410, mercury, cotton waste, thinner, diesel, department of instrumentation engineering, arduino uno, raspberry pi 5 with - 16gb,bcm2712 2.4ghz quad-core 64-bit arm cortex-a76 cpu,2 usb 2.0 ports, 2 usb 3.0 ports, bluetooth 5.0 / bluetooth low energy (ble),gpio standard 40-pin gpio header, video and sound 2 micro hdmi ports (up to 4kp60 supported), 4-pole stereo audio and composite video port, on board ports 1 x dsi, 1 x ethernet, 2 x micro hdmi, 2 x usb 2.0, 2 x usb 3.0, 40-pin 2.54 mm (2 20 strip) gpio, usb type-c port, micro sd card slot - supports high-speed sdr104 mode and raspberry pi 5 case-red-white, micro sd card 32gb, power supply and memory card reader., ir sensor module, pir sensor module, ultra-sonic sensor module, heat sensor module, temperature and humidity sensor module, blue tooth module, mq 3 air quality/gas detector module, ultrasonic sensor module, motor driver module- l298, buzzer, colour recognition sensor module, desoldering pump, battery 9v, diode 1n 4007, ujt 2n2646, regulator ic - 7805, regulator ic - 7809, regulator ic
Tender For supply of inserted t slot cutter head 3.81mm width spec. for manufacturing of front sight bed (ak-203) with ha , steel shank dia 12mm with t08 thread connection oal 90mm for manufacturing of front sight bed (ak-20
Tender For supply of cutter t slot milling finishng dia 27.65-0.10mm x oal 140mm as per hvf drg. no. dm63395 , cutter tslot milling roughing dia 27mmxoal140mm to is 5103-69 hss m35 tin coated singlepiece constrn
Tender For supply of single inserted t-slot cutter, dia= 20-22mm, width= 4mm, corner radius not more than 0.1mm, no. of flu , through coolant shank for inserted t-slot cutter, dia= 20-22, shank dia= 16mm, oal= 70mm(minimum) , neck
17 Jan, 2026
NA
